BRESSER Slider Binocular Mount with Tripod

The BRESSER Slider Binocular Mount, with its revolutionary design, offers unprecedented comfort for binocular observation - during the day and at night Thanks to the variable extension length of the two support rails (crossbars), the cardanic mount head and various adjustable slip couplings almost all binocular positions can be selected easily. Afterwards, the binoculars remain in their respective position thanks to the counterweights. During observation, it is usually not necessary to touch the binoculars. Whether you want to observe standing up, sitting on a swivel chair or lying down on a mat or bed, everything is possible. For wheelchair users the mount is also an interesting alternative to normal tripod solutions, where usually one tripod leg is always in the way. A steady image despite large binoculars and high magnification Especially when observing for a long time, even medium-weight binoculars weighing 500 grams or more and moderate magnifications of 10x or more make life difficult. Already after a short while the pictures blur and the arms get tired. Certainly, a high photo tripod can bring a significant improvement. But this solution is very limited in terms of the binoculars’ movability and the position of the observer. The BRESSER Slider Binocular Mount offers far more possibilities. Almost all desired binocular positions can be reached effortlessly. The patented design, with 2 counter-moving support rails (crossbars), is guided on special linear roller bearings inside the mount head with zero play. This allows the observer to vary the extension length as desired with little muscle power. The sliding resistance can be infinitely adjusted using 2 adjusting screws. In the middle of the slider mount’s centre of gravity, there is an axle with adjustable slipping clutch for the tilting and rotating movement. All bearings operate with absolute precision and backlash-free. For quick levelling, there is even a 30 mm fluorescent circular bubble in the base of the mount, which is easy to read even in the dark. Cardanic mount head The cardanic mount head works like a ball head. However, it offers a significantly higher load-capacity and more stability. Here, too, the sliding resistance of all moving parts can be adjusted to the user’s specific needs. The mount head offers several mounting holes for mounting a binocular holder via 1/4-inch photo screw or a standard GP prism clamp for mounting small telescopes. In addition, there are various holes on the side cheeks of the mount head for further accessories such as red light reading lamps, smartphone holders for the use of sky apps or LED viewfinders for quick sighting of celestial objects. Counterweights Several counterweights enable the exact balancing of the binoculars or telescope. Two counterweights of each 2.5 kg, 1.25 kg and 0.5 kg are included in the package and can be attached to the rear end of the mount on the mounting bolts on both sides. With the 2 included spring clamps the weights are secured on the bolts. Instead of the counterweights, a filled sandbag can also be attached to the existing mounting hook. This reduces the transport weight for planned excursions. Suitable for use with binoculars of up to 3.5 kg weightThe BRESSER Slider Mount can be used with binoculars of up to 3.5 kg weight. But it is also a real help for obtaining blur-free images with much smaller binoculars during long-term observations. It is mounted with an optionally available binocular tripod adapter, which is attached to the mount head with a 1/4-inch photo thread screw. Also highly recommended for compact refractor telescopesInstall an optionally available standard GP prism adapter on the mount head and use your travel telescope in a completely different way: as a high-quality spotting scope for landscape and sky observation. Tripod adapter The matching tripod adapter for using the optionally available BRESSER stainless steel Tripod ST-3 (item no.: 0114310) is already included in the slider mount’s scope of delivery. It converts the standard large 3/8-inch photo tripod thread (internal thread) in the base of the slider mount into a metric M10 thread. This means that after removing the adapter, a stable standard photo or video tripod with 3/8-inch mounting screw can also be used.GETTING STARTED VIDEO:  https://www.youtube.com/watch?v=AhJm3Cl1e9IFEATURESBRESSER Slider Binocular Mount without Tripod Enables comfortable and fatigue-free binocular observation Suitable for landscape and sky observation Shake-free and steady images at day and night Almost infinitely rotatable and swivelling cardanic mount head Supports binoculars and telescopes up to 3.5 kg weight Various observer positions are possible: standing, sitting and lying down Also a practical alternative to a photo tripod for wheelchair users Adjustable viewing height from approx. 30 cm to 170 cm (when using the BRESSER tripod, item no. 0114310)Dimensions when fully assembled: 125 x 35 x 180 cm (when using the BRESSER tripod, item no. 0114310)Total weight mount head incl. accessories: 14.5 kgWeight of mount head: 6 kg  Large 30 mm fluorescent circular bubble in the mounting base Mounting holes for further optional accessories available Several balance weights include: 2x 2.5 kg, 2x 1.25 kg, 2x 0.5 kg Adjustable friction clutches on all movable axes All surfaces high quality painted, powder coated or anodised Precise small series production - manufactured in the EU (Hungary)SCOPE OF DELIVERYSlider mount (binoculars + tripod not included)Tripod adapter 3/8 inch to M10 thread Balance weight 2.5 kg (2 pieces) Balance weight 1.25 kg (2 pieces) Balance weight 0.5 kg (2 pieces) Locking device for counterweights (2 pieces)

SPEZIAL ASTRO binoculars from BRESSER are ideal for astronomy and landscape observation. This is a professional large binocular with ED glass objective lenses for the very highest demands on color fidelity and brilliance. With the best viewing characteristics, a robust marine version and a sturdy tripod adapter. Thanks to fully multi coated Bak-4 glass material, the extra large objective lens diameter and highly corrected eyepieces with 5 lenses in 3 groups these binoculars provide bright, crisp images from edge to edge. The high 20x magnification it is convenient not only for observing astronomical objects but is also practical for viewing distant terrestrial objects. Due to a very high reduction of stray light, the binoculars deliver the best possible picture and a perfect sight. With the individual eyepiece focus once set you can get a sharp image for all astronomical distances. Foldable rubber eyecups give eye glass wearers the possibility of making the best use of these optics’ field of view. The binoculars are waterproof and ARGON gas filled to avoid internal fogging. The ergonomic rubber armouring provides a good grip and is also protected against shocks. With the included heavy duty foto tripod adapter the SPEZIAL ASTRO ED can be mounted onto any foto tripod which offers a standard 1/4inch or 3/8inch thread. The use of a tripod is also highly recommended at a high magnification of 20x to obtain a steady image. FEATURES Binoculars for astronomical and landscape observations Extremly high light gathering capacity  High magnification for for distant objects Fully multi coated optics Waterproof and ARGON gas filled against fogging Magnification: 15x / objective lens diameter: 70mm Individual eyepiece focus and foldable rubber eyecups Highly corrected eyepieces for crisp images from edge to edge Ergonomic rubber armouring - protected against shocks Dimensions: 310x250x100mm / weight: 2700g Heavy duty foto tripod adapter included SCOPE OF DELIVERY Binocular Photo tripod adapter Neckstrap Dust covers CaseInstruction manual

Do you already own a photo camera and would like to create impressive pictures of the night sky with the help of the long exposure or even make time-lapse pictures with little effort? The BRESSER StarTracker Astronomical Photo Mount Kit is the ideal base. Not only for beginners in astrophotography, this mount is particularly well suited, but also the experts swear by a compact and easy-to-use mount to automatically compensate for the natural rotation of the earth. The built-in tracking motor rotates the saddle-mounted camera precisely against the earth's rotation and thus the stars remain in pinpoint shape even with long exposures. This set contains all the components required for a quick and comfortable entry into the world of astrophotography with the exception of a camera and objective lens: A stable BRESSER tripod TP-100 DX with carrying bag, the BRESSER Micro Motion Head MH-100 (polar-wedge), the BRESSER Polar Finder Scope for StarTracker PM-100 and of course the BRESSER StarTracker astrophoto mount PM-100 with ball head.Which cameras are basically suitable for use with the BRESSER photo mount? All cameras with 1/4'' (6.3mm) tripod connection thread and bulb length B for long exposure are suitable. The BRESSER StarTracker Astronomical Photo Mount PM-100 is designed for a camera with lens of max. 2.0 kg total weight to carry and track in polar mode. In Azimut mode also a camera weight up to 5.0kg is possible.  Large aperture, wide-angle lenses are ideal for the beginning, because the requirements for tracking accuracy accumulate with increasing focal length and exposure time. Thus, a shot with wide-angle lens can be exposed for up to several minutes and the stars remain punctiform without problems. For example, with a 200mm telephoto lens the polar alignment of the photo mount must be exactly right. But thanks to the delievered optical Polar Finder Scope, this is done quickly. After setting up the light and compact StarTracker Photo Mount, simply set the approximate latitude (pole height) and aim Polaris through the integrated Polar Finder Scope. Then mount the camera with the photo lens using the quick-release plate on the supplied ball head. With the ball head, the camera can be aligned and determined at any time on any section of the sky. As soon as the tracking motor is switched on, long-time exposure can be started immediately. This does not even take 5 minutes ... The tracking is carried out by a precise stepper motor, which can be controlled by an easy digital setup on LCD screen. Low power consumption allows up to 20 hours of operation with just one battery charge or simply use the micro USB port for an unlimited power supply. Typically achievable exposure times with good tracking accuracy are: 16mm wide-angle lens: 5 minutes (300 sec.) , 100mm telephoto lens: 1 minute (60 sec.) FEATURES StarTracker Astronomical Photo Mount Kit Equatorial StarTracker Photo-MountAutomatic siderial tracking against the Earth rotation  Different tracking speed setting possible Suitable for northern and southern henisphere Time lapse: from 15 minutes to 48 hours Ballhead with quick release saddle plate and 1/4'' Photo thread for Kamera mountingPhoto-Mount with 1/4'' threaded bolt for ballhead mounting Additional quick release coupling for ball head removal High precision stepper motor with helical gear for accurate tracking Clear LCD screen and easy setup menu Battery operation 4 x AA batteries or mico USB (optional acc.)  Battery life: up to 20 hours Weight Photo-Mont: 0.63kgTransport weight incl. complete accessories: 3.6 kg Adjustment height mount with tripod: 80-155cm Tripod transport dimensions: 60x10x10cm; tripod weight: 2,1 kg Load capacity of Photo-Mount: up to 2.0kg/5.0kg (EQ/AZ) SCOPE OF DELIVERY BRESSER StarTracker astronomical Photo-Mount PM-100BRESSER Ballhead with quick release saddle plateBRESSER Polar Finder Scope for StarTracker PM-100BRESSER Micro Motion Head MH-100 (Polar-Wedge)BRESSER Tripod TP-100 DX with carry bag User manual 

Whether you want to explore the night sky or make terrestrial observations during the day, the BRESSER NightExplorer 15x70 astronomy binoculars will ensure that you are perfectly equipped for all your outdoor adventures. The extra large lens diameter of 70 mm lets a large amount of light into the binoculars, while the 15x magnification ensures that you obtain highly detailed images of your observed targets. Fully multicoated optics ensure scattered light is kept to a minimum, so that you can enjoy a perfect view with the best possible optical performance. At a distance of 1000 metres, the field of view is 77 metres wide. The highly corrected eyepieces with 5 lenses in 3 groups produce vivid images with sharp edges. Coating The premium BaK-4 optics (barium crown glass) features a full multi-coating to increase light transmission and reduce reflections. Focusing Thanks to the individual eyepiece adjustment, you only need to focus the binoculars once. You can then enjoy a sharp image at infinity for the night sky. The binoculars also have a close focus, which you can set from a distance of 10 metres or more for close-up observations of your immediate surroundings. Also suitable for glasses wearers Thanks to the foldable eyecups, you can set the optimal distance between your eyes and the ocular lenses. If you wear glasses, this allows you to see the entire field of view of the Porro-prism binoculars. There is also a dioptre compensation of +/-8, which you can use to compensate for small differences in vision between your eyes. Weatherproof and robust Thanks to their waterproof design, the binoculars can be used in wet or foggy weather conditions, as water and moisture cannot enter the housing. The binoculars are filled with argon to stop the optics from fogging up. In addition, the ergonomic armouring provides a secure grip and protects the binoculars against impacts and knocks, making them ideal to travel with. Portable design The 15x70 Porro-prism binoculars come with an excellent lightweight aluminium tripod, with study ballhead mounting, to ensure wobble-free astronomical or terrestrial observations. Both the binoculars and the tripod can be stored in the sturdy padded backpack, which is also included in the set. This ensures that you can easily transport your gear to your desired vantage point, even if you have to go a long way to get there. Discover the night sky and the wonders of nature with the powerful BRESSER NightExplorer 15x70 astronomy binoculars! FEATURES Astronomy binoculars for astronomical and terrestrial observations High magnification and light-gathering power Magnification: 15x Lens diameter: 70 mm Optical design: Porro Full multi-layer coating BaK-4 glass material Rubber eyecups for spectacle wearers Individual eyepiece adjustment Highly corrected eyepieces for sharp-edged images Field of view: 77 m (at a distance of 1000 m) Close focus: from 10 m Dioptre adjustment: +/- 8 Tripod connection thread Includes Aluminium tripod Includes Backpack WHAT'S INCLUDED Astronomy binoculars Tripod Backpack Instructions with warranty information

Take a look through the new Vixen BT-81S-A binocular telescope. This model is ideal for observing gas nebula, star clusters and comets. The magnesium fluoride coating reduces chromatic aberration and the large aperture of 81 mm ensures a razor-sharp, contrast-rich image. Weighing just 4.1 kg, the BT-81S-A binocular telescope is very transportable. FEATURES Objective lenses: 81 mm 2-lens achromat, multi-coated Focal length: 480 mm (f5.9) Resolution and limiting magnitude: 1.43 arc seconds; 11.3 Light-gathering power: 134x Dimensions and weight: 480 x 190 x 155 mm; 14.0 kg Adapter and connections: 31.7 mm clamp WHAT’S INCLUDED HF2 fork mount SXG-HAL130 tripod Carry handle finder shoeDew caps 2 SLV 20 mm eyepieces Swing bracket binocular cradle

Adding one or more accessory bays will provide you with additional storage for your computer, books, etc. ​It is advisable to purchase these bays at the time of purchasing your observatory. This will save the extra delivery charge at a later date. The accessory bay comes with fixing kit and full installation instructions.  DIMENSIONS: 1050mm high x 680mm wide x 500mm deep , weight: 15 kgSCOPE OF DELIVERYBay (1 piece)

The BRESSER DST-0745 is a special microscope that is operated with a c-mount camera (camera not included). This allows direct viewing on a screen. Due to the vertically installed optics, there is no shifting of the image when focusing. This is especially useful for "focus stacking" shots. The zoom is continuously adjustable from 0.7x - 4.5x. A coarse and fine focus adjustment facilitates focusing, especially at high magnifications. The convenient and user-friendly operation makes the digital microscope particularly suitable for daily use in the workshop. Measurements, quality control of surfaces or inspection of components and raw materials are easy with the workshop microscope. Insects, plants and rocks are also impressively displayed. The DST-0745 workshop microscope is not suitable for visual observation. It can only be used in combination with a MikroCam c-mount microscope camera. It is designed for camera sensors of about 1/2". Smaller sensors can be used without problems. With larger sensors there is vignetting, which becomes somewhat less at higher magnifications. Due to the two flexible incident light lamps, the light can be optimally positioned. The transmitted light illumination helps when observing transparent objects. The brightness of both illuminators can be adjusted in five steps. The magnification of a USB camera differs from the magnification of the lens. It depends, among other things, on the sensor size and the display on a monitor. It can be compared to macro lenses with macro factor 0.7:1 up to 4.5:1. Compatible MikroCam cameras: 5914131 MikroCam SP 1.3 MP 5914320 MikroCam SP 3.1 MP 5914520 MikroCam SP 5.0 MP 5914004 MicroCamII 5914020 MicroCamII 5914310 MicroCamII 5914912 MicroCamII 5914180 MikroCam PRO HDMI 5914190 MikroCam PRO HDMI 5MP 5914195 MikroCam Pro HDMI Autofocus FEATURES Designed for C-mount microscope cameras Up to 1/2" sea sensor size Continuous zoom (0.7x - 4.5x) Two flexible incident light LED lamps LED transmitted light illumination Adjustable brightness SCOPE OF DELIVERY Zoom lens head 0.7x - 4.5x Stand with incident and transmitted light illumination Object plate glass (one side frosted) Object plate plastic (one side white, one side black) Power supply unit, operating instructions, dust cover