EXPLORE SCIENTIFIC MPCC Field Flatt. ED APO+Canon EOS T2

The image plane of many telescopes is not plane, but curved. This results in a picture that has its optimal focus only in the center of the field of view - the edge of the field is out of focus and thus unsharp. The human eye is able to accomodate most of this but a camera will show stars that get increasingly unsharp towards the edge of the field. The Explore Scientific Multi Purpose Curvature Corrector eliminates field curvature in a variety of telescopes - Explore Scientific Apos and many other refractors and cassegrain telescopes. This increases the edge sharpness in the image drastically. Improves edge sharpness not only with Explore Scientific Apos, but also with many other refractor and cassegrain telescopes. This image field leveller fits all Nikon DSLR cameras, but can also be used for other camera types due to the universal T2 thread connection. This requires an optional camera-specific T2 ring. SPECIFICATIONSImage flattener for Nikon DSLR cameras Eliminates the field curvature of ED APO telescopes Can also be used for various cassegrains The image sharpness at the edge is drastically increased 2 inch/50.8mm push-in connector with filter thread T2 threaded connection (M42x0,75mm) Full multi-coating on all lens surfacesStainless steel housing Adapter for Nikon F bayonet included DELIVERY SCOPE Bildfeldebner Nikon (1 piece)

Field flattener without reduction factor for Explore Scientific ED80 , ED102 and ED127 APO Refractors The imaging plane of many telescopes is not flat but curved. This means that only the area in the centre is perfectly focused - the edge becomes blurred. The human eye can usually compensate for this image property, but a camera shows increasing blurriness towards the edge of the image field. The Explore Scientific Zero X field flattener eliminates the field curvature in many telescopes with a focal length of approx. 480 to 952 mm. The Zero X field flattener was calculated and developed for Explore Scientific ED80, ED102 and ED127 apochromats with focal ratios of F=6.0 and F=7.5. The image sharpness at the edge is dramatically increased. The stars appear round and no longer distorted - a clear benefit for the whole image aesthetics. The Zero X image flattener can be used not only with Explore Scientific Apos, but also with many other Apos. This flattener does not change the focal length of the telescope. Correction for up to full-frame camera sensors (24x36mm) The Explore Scientific Zero X image flattener has been developed due to the rapid development of ever larger camera sensors. With it, there is finally a field flattener available that illuminates and corrects the field of view for full-frame camera sensors up to 24x36 mm. How to use the Zero X field flattener with M48 thread connection This field flattener has a 2 inch (50.8 mm) plug-in connection on the telescope side, with which it is inserted into the telescope instead of an eyepiece or star diagonal mirror. On the camera side, there is a standardised M48 x 0.75 mm connection thread. This M48 connection thread offers a larger free inner diameter than the usual T2 (M42) thread and prevents vignetting when using large camera sensors. With an optionally available and camera-specific adapter ring, a DSLR camera can be connected to it. The working distance is already set at 55 mm. Of course, mirrorless cameras or special astro cameras can also be used with the M48 thread connection. For this, the appropriate M48 spacer sleeves or adapters are additionally required to set the right working distance of 55 mm. This must always be done with every corrector or field flattener so that the best possible field flattening is achieved.Filter thread on telescope side availableThe telescope-side 2.0 inch plug-in sleeve has an M48x0.75 filter thread (internal thread). Individual 2.0 inch colour or nebula filters can be inserted here to increase the contrast of the images.FEATURESField flattener for Explore Scientific ED80, ED102 and ED127 APO telescopesRemoves field curvature from telescopesProduces round stars even at the edge of the image fieldImage sharpness at the edge is drastically increasedA clear benefit for the whole image aestheticsCorrection of field curvature for up to full-frame camera sensors (24x36 mm)Image field flattener without reduction factorOn the telescope side with 2 inch (50.8 mm) plug-in connection and M48x0.75mm filter threadCamera side with large M48 threaded connectorWorking distance of 55 mm between field flattener and camera sensorFor telescopes with a focal length of approx. 480 to 952 mmOptimised for telescopes with focal ratios from F=6.0 to F=7.5Can also be used for various other APOsFully multi-coating on all lens surfacesHousing made of lightweight aluminium, black anodisedAluminium dust cap for M48 threadSCOPE OF DELIVERYZero X field flattener (1 piece)Dust caps

After three years of testing and refining we are extremely proud to present the new Explore Scientific High Resolution (HR) Coma Corrector. This corrector is a class of it´s own - it is fully functional for visual use and expands the focal length by only 6%! The Explore Scientific Coma Correktor is delivered as a complete set together with a rotating helical focuser with laser-etched scale, so you get a full package: corrector, adaptor to T2 (M42x0.75mm), adaptor to M48 (M48x0.75) and the helical focuser for visual fun. This coma corrector really is "high resolution" - it deliveres a visual polystrehl performance of 0,98 at f/4 and 0,96 at f/3! So it can stay in the telescope - and you will not only enjoy a tack-sharp Jupiter, but aslo sharp and defined moons in the future! What this means in terms of performance is shown in the three pictures with the graphs - the sharpness increase in those comparisons with and without corrector are stunning (examples are 400mm f/4, f/3,5 and f/3). Please notice: These graphs are for FLAT FIELD! You will get this performance without refocussing! Diameter of the field is 30mm - it doesn´t make sense to increase this with 2" and fast optical systems. Length of the 2" corrector barrel is approx. 85mm and it can be used with almost all 2" focusers on the market. To use the HR Coma Corrector visually, you need to have at least 32mm spare inward travel at your focuser, while the focus is on the same plane as the focusers end. Photographically there is no problem - the HR Coma Corrector shifts the focus outward by about 35mm, so that you will have no problem in achieving focus, when you are able to focus your camera without the HR Coma Corrector. FEATURESEliminates coma, field-curvature and astigmatism in newtonians Diffraction limited performance on axis and in the field Flattens the field Works for very fast systems down to f/3 Four-lens construction Can be used with almost all 2" focusers on the market SCOPE OF DELIVERY High Resolution (HR) Coma Corrector Adaptor to T2 (M42x0.75mm) Adaptor to M48 (M48x0.75) Helical focuser

Do you already own a photo camera and would like to create impressive pictures of the night sky with the help of the long exposure or even make time-lapse pictures with little effort? The BRESSER StarTracker Astronomical Photo Mount Kit is the ideal base. Not only for beginners in astrophotography, this mount is particularly well suited, but also the experts swear by a compact and easy-to-use mount to automatically compensate for the natural rotation of the earth. The built-in tracking motor rotates the saddle-mounted camera precisely against the earth's rotation and thus the stars remain in pinpoint shape even with long exposures. This set contains all the components required for a quick and comfortable entry into the world of astrophotography with the exception of a camera and objective lens: A stable BRESSER tripod TP-100 DX with carrying bag, the BRESSER Micro Motion Head MH-100 (polar-wedge), the BRESSER Polar Finder Scope for StarTracker PM-100 and of course the BRESSER StarTracker astrophoto mount PM-100 with ball head.Which cameras are basically suitable for use with the BRESSER photo mount? All cameras with 1/4'' (6.3mm) tripod connection thread and bulb length B for long exposure are suitable. The BRESSER StarTracker Astronomical Photo Mount PM-100 is designed for a camera with lens of max. 2.0 kg total weight to carry and track in polar mode. In Azimut mode also a camera weight up to 5.0kg is possible.  Large aperture, wide-angle lenses are ideal for the beginning, because the requirements for tracking accuracy accumulate with increasing focal length and exposure time. Thus, a shot with wide-angle lens can be exposed for up to several minutes and the stars remain punctiform without problems. For example, with a 200mm telephoto lens the polar alignment of the photo mount must be exactly right. But thanks to the delievered optical Polar Finder Scope, this is done quickly. After setting up the light and compact StarTracker Photo Mount, simply set the approximate latitude (pole height) and aim Polaris through the integrated Polar Finder Scope. Then mount the camera with the photo lens using the quick-release plate on the supplied ball head. With the ball head, the camera can be aligned and determined at any time on any section of the sky. As soon as the tracking motor is switched on, long-time exposure can be started immediately. This does not even take 5 minutes ... The tracking is carried out by a precise stepper motor, which can be controlled by an easy digital setup on LCD screen. Low power consumption allows up to 20 hours of operation with just one battery charge or simply use the micro USB port for an unlimited power supply. Typically achievable exposure times with good tracking accuracy are: 16mm wide-angle lens: 5 minutes (300 sec.) , 100mm telephoto lens: 1 minute (60 sec.) FEATURES StarTracker Astronomical Photo Mount Kit Equatorial StarTracker Photo-MountAutomatic siderial tracking against the Earth rotation  Different tracking speed setting possible Suitable for northern and southern henisphere Time lapse: from 15 minutes to 48 hours Ballhead with quick release saddle plate and 1/4'' Photo thread for Kamera mountingPhoto-Mount with 1/4'' threaded bolt for ballhead mounting Additional quick release coupling for ball head removal High precision stepper motor with helical gear for accurate tracking Clear LCD screen and easy setup menu Battery operation 4 x AA batteries or mico USB (optional acc.)  Battery life: up to 20 hours Weight Photo-Mont: 0.63kgTransport weight incl. complete accessories: 3.6 kg Adjustment height mount with tripod: 80-155cm Tripod transport dimensions: 60x10x10cm; tripod weight: 2,1 kg Load capacity of Photo-Mount: up to 2.0kg/5.0kg (EQ/AZ) SCOPE OF DELIVERY BRESSER StarTracker astronomical Photo-Mount PM-100BRESSER Ballhead with quick release saddle plateBRESSER Polar Finder Scope for StarTracker PM-100BRESSER Micro Motion Head MH-100 (Polar-Wedge)BRESSER Tripod TP-100 DX with carry bag User manual 

Solar observation in H-Alpha: prominences, filaments, flares ... the most spectacular way to see the Sun - easy and affordable with the LS40THa.Complete H-alpha solar telescope with 40mm aperture, <0.7 Angstrom bandwidth, B500 blocking-filter, and Helical focuser.The LS40THa/B500 is a complete telescope for observing the sun in H-alpha, with 40mm aperture (no central obstruction) and 400mm focal length. The H-alpha wavelength is the most impressive way to observe the sun, showing protuberances at the sun's edge, filaments and flares on the surface, and much more. An Etalon with mechanical tilt-tuning provides <0.7 Angstrom bandwidth.Fine adjustment is achieved with a 1.25 inch Helical focuser. Blocking-filter is the B500, this is good for visual observation of the sun. The star diagonal in which the blocking filter is installed, is equipped as standard for 1.25 inch eyepiece connection.The easy handling makes this telescope ideal for starting H-Alpha solar observation. Due to its compact dimensions it is also a good travel telescope for the experienced solar observers.The LS40THa telescopes are available with choice of B500, B600 or B1200 blocking filters. The larger blocking filters provide less edge obstruction and a larger field of view for visual observation and photography. Please note that these telescopes have only a very small back focus and therefore photography is difficult. We recommend special astro cameras for photography, which have a very short distance to the sensor, such as the BRESSER Full HD camera item number 4959050.FEATURESAperture: 40mm (no central obstruction, 2-lens refractor)Focal length: 400mmBandwidth: <0.7 AngstromTuning: mechanical tilt-tuningBlocking filter: B500 with 1.25 inch connectionFocuser: Helical focuserDovetail bar at standard GP-level1/4-20 tapped base (standard thread for photo-tripods)Sol-Searcher includedWeight: 1.2kgLength: 41cmSCOPE OF DELIVERYLS40THa Solar TelescopeB500 blocking filter in star-diagonal housing1.25 inch Helical focuserDovetail bar (GP level)Sol-SearcherInstruction manual

Discover the possibilities and forge new paths with the Nebula EXOS-2 Goto Mount!Mount and TripodThe BRESSER EXOS-2 is a stable mount with a high load capacity and precise tracking for visual observations and astrophotography. Double radial groove ball bearings in both axes ensure precise, smooth motion, and the RA axis bearing has been optimized to reduce backlash. Additionally, the tripod is reinforced to further suppress vibrations. The BRESSER EXOS-2 can be loaded with up to 13 kg of optics for purely visual use depending on the length and purpose!Nebula: the powerful and flexible Goto systemWith the new Nebula Goto system, set off for new astronomical shores. This system offers several control options. You can operate the mount directly via its own Nebula control interface using your smartphone or tablet (iOS and Android supported). Alternatively, you can also use a planetarium software such as SkySafari. Manual control remains an option as well. For this, a hand box for minor corrections or simple control commands is included.Furthermore, with the BRESSER Nebula Goto Kit, you can connect your laptop or PC directly via WIFI or LAN cable (recommended for faster data transfer) to the Nebula control unit. This not only gives you full control over the mount but also allows you to connect various devices such as cameras, motor focus, filter wheels, etc. directly to the control unit via various USB ports. This eliminates the need to connect each device to your computer via cables. The pre-installed program KStars / EKOS lets you comfortably control all devices from your PC or laptop. Electronic polar alignment or guiding can also be easily achieved with the Goto Kit, provided you have a camera connected. You are also not limited to the software of the Nebula control unit. Thanks to the installed ASCOM Alpaca driver, you can use your own programs on your computer to control the mount - whether it's Stellarium or N.I.N.A. The two stepper motors with a belt drive ensure a smooth, direct drive of the two axes. It's only important to have a good balance. FEATURES EXOS-2 MOUNT Stable parallactic mount with fine drive in both axes Ball bearings in both axes for more precise movements Sturdy height-adjustable stainless steel tripod (Min. 69 cm / Max. 109.5 cm) Load capacity of up to 13 kg Spirit level for easy horizontal alignment Polar height scale for setting the latitude Polar scope with optional lighting (item no. 4964212) Tripod weight: 4.7 kg Mount weight: 5.6 kg (without counterweight) Total weight including counterweight: 14.8 kg Batteries: not included FEATURES GOTO SYSTEM Belt drive for a more precise, quieter tracking Stepper motors with high resolution (0.36´/microstep) Hand control box for direct control of the mount Virtual hand control box for smartphones and tablets PC control – ASCOM compatible USB ports for cameras, motors, filter wheels etc. SCOPE OF DELIVERY BRESSER EXOS-2 Mount Polar finder scope with optional illumination Stainless steel field tripod with accessory tray 1x 4.5-kg counterweight 2 stepper motors for the axes (RA and DEC) Raspberry Pi control unitBasic handbox 230V / 12V / 3 A power adapterConnection cableManual for download

The Vixen focal adapter can be used to connect your DSLR camera to your telescope via a 60-mm thread. The large internal diameter of the adapter prevents shadows at the edges of the image when using a full-frame DSLR camera. The focal adapter can also be rotated to rotate the field of view selection. Three locking screws are provided for clamping.Note: Vixen T2 ring also required for your Canon. In this case, the inner ring is removed from the T2 adapter and clamped using three small grub screws.FEATURES60-mm connection thread for OAZWeight: 56 gT-ring for Canon EOS also requiredPACKAGE CONTENTSVixen focal adapter for Canon EOS