Vixen AXJ-TR Tripod adapter set (conversion adapter)

The declination body unit allows you to expand the AP Photoguider to a complete equatorial AP mount with mototized RA and DC axes. You can move and track the mount in both axes. In addition, you will need the Manual Fine Adjustment Module, or the DEC motor module, as well as the AP counterweight rod and a counterweight. The counter weights of the SX mount series can all be used on the counter weight rod. The APZ counter weight can also be attached to this unit. The built-in battery compartment serves as an additional power supply and is powered by 4 AA batteries.  FEATURESExtends the AP Photoguider to an EQ mount Allows the DC motor module to be attached Built-in power compartment for 4x AA batteries Makes guiding in RA and DC possible SCOPE OF DELIVERYAP declination body Mounting screws Mounting tool

Designed as a complement to the AXD2 equatorial mount, the AXJ mount offers outstanding durability and precision. The AXJ mount can also be used on AXD-TR102 tripods with an adapter. Periodic errors on mounts are usually measured and corrected by the user. Unlike the old StarBook controller, the STAR BOOK TEN controller saves these errors permanently. The periodic error of the mount is measured in the factory (total of 12 points per 30 degrees worm gear) and corrected before delivery. This is known as V-PEC and functions automatically as soon as you use the mount. It delivers an accuracy of +/- 4.0 arc seconds. You can increase the tracking accuracy further by saving your own recorded periodic errors. Vixen uses a new Belt-drive system in the AXJ mount. The gear drive was replaced with a toothed belt drive. This gives the mount a quicker reaction time and lower backlash. It also helps to minimize noise. The 6x20 polar finder scope is pre-installed. This allows the user to configure the polar alignment (for both the northern and southern hemispheres). The polar finder scope has a variable illuminated reticle with an automatic power-off function. The brightness can be adjusted in 8 levels so that the user can configure the desired brightness. SETTING ACCURACY OF LESS THAN 3 ARC MINUTES The dark field illumination (red LED) turns on when the push button is pressed. The reticle also lights up in red so that the observer can recognize and align stars in the background of the reticle. The light turns off automatically after a few minutes to save battery power. 2 bearing sets (4 pieces) are used for the shaft of the RA axis. Thanks to the newly developed EQ design, the ZXJ mount has a higher load capacity of 22 kg. As the motors, worm shaft and worm gear are located in the lower part of the mount, fewer counterweights are required than with conventional mounts. The STAR BOOK TEN controller is a modern control system with a high-resolution colour monitor. The STAR BOOK TEN system contains more than 272,000 celestial objects, including 260,000 stars from the SAO catalogue, 109 Messier objects, 7840 NGC objects and 5380 IC objects, as well the soon, moon and planets. Objects can be accessed by name, and information such as images and data can be defined separately. FEATURES +/-4.0 arc seconds with V-PEC V-PEC (Vixen-Permanent Periodic Error Correction) Belt drive system (prevents backlash and minimizes noise) 14 ball bearings Polar alignment (variable fork fix type) Polar finder with reference star alignment STAR BOOK TEN controller with autoguider input Retractable counterweight bar WHAT’S INCLUDED AXJ mount Starbook Ten controller 2 counterweights (3.7 kg and 1.5 kg) GoTo mount with Star Book Ten controller 22 kg load (photographic)

Mounting head for securing Vixen standard dovetail bars. The unique friction control system enables you to move the telescope by hand without loosening the clamping lever. The included AP clamping lever allows the mount to be clamped more tightly if needed. The module is compatible with the AP mount head, but cannot be used with the AP Photoguider. The module has a hole in the centre to ensure the polar finder has an unobstructed view. FEATURES Type: Dovetail holder with slip clutch system with clamping and locking screwAxle clamp: Delivered with AP clamping lever Bearings: 1x ball bearing Dimensions: 78 x 56 mm without extrusion parts Weight: 345 gDELIVERY CONTENTAP mounting head moduleAP clamping lever Clamping screw for dovetail barLocking screw

Tripod head with fine adjustment for fast and precise pole height adjustment of the BRESSER StarTracker Astrophoto Mount PM-100 art. no. 4964120. The BRESSER Micro Motion Head MH-100 allows a very precise adjustment by using large dimensioned knurled screws. In order to keep the adjustment distances by using the knurled screws as small as possible, the mounting plate has a quick-release clamping device with toothing in order to be able to select a rough presetting of the pole height (latitude at the location). The Micro Motion Head MH-100 can be mounted on any photo tripod with 1/4 inch photo thread closure. The BRESSER StarTracker astrophoto mount can then be mounted on the MH-100 tripod head without the use of tools using a 1/4" photo thread screw. The complete  motion head is made of black anodized aluminum and guarantees highest stability by the use of solid material. The knurled screws with fine pitch thread are even made of stainless steel and guarantee a long durability and corrosion resistance. Ideal for optimizing tracking accuracy in astrophotography. IMPORTANT NOTE: Can also be used as a stable adjustment element of a telescopic sight in astrophotography. Parallel alignment of the main telescope and the guide telescope is thus also possible quickly and precisely. Base plate connection: 3 x 1/4 inch photo thread with 35.0 mm hole spacing. Mounting plate connection: 2 x M8x1.25 thread with 35.0mm hole spacing. FEATURES Compact micro motion head with fine adjustment Functions as a so-called polar-wedge For precise adjustment of polar alignment (EQ mode)Mounting plate with quick-release clamping device and toothingCan be used with any photo tripod and 1/4inch thread adapterMade of black anodised aluminium and stainless steel Quick and easy to use deviceSuitable for BRESSER StarTracker Astrophoto Mount PM-100 Suitable for BRESSER tripod TP-100 DX  Also ideal as an adjustment element of an auto-guiding scopeFor parallel alignment of main telescope and guiding telescope Base plate connection: 3 x 1/4 inch photo thread; hole spacing 35.0mm Connection mounting plate: 2 x M8x1.25mm thread; drilling distance 35,0mm SCOPE OF DELIVERY Micro Motion Head MH-100 Instruction manual

The Vixen POLARIE Multi Mounting Block was developed to fit Vixen profile dovetail rails, such as the Vixen Dovetail Slide Bar DD, to the Polarie Star Tracker. In this way you can increase the load capacity of the tracker up to 6.5 kg! By releasing the clamping lever on the multiple assembly block, you can move the dovetail freely and clamp it again, making balancing of your camera or telescope rig an easy task. The hole in the middle of the multiple mounting block enables the photographer to carry out the polar alignment without removing the POLARIE polar finder PFL with the dovetail rail DD or the dovetail rail PG. Using one of these combinations, you can easily put deep sky photography into practice with a telephoto lens, or compact telescope. PROPERTIES Allows the inclusion of dovetail rails The Star Tracker can hold up to 6.5 kg in weight Allows the use of telephoto lenses Polar alignment possible without removing the polar finder Weight: 440g WHAT'S INCLUDED POLARIE multiple assembly block Assembly tool