Vixen Encoder for AXJ Mount

Designed as a complement to the AXD2 equatorial mount, the AXJ mount offers outstanding durability and precision. The AXJ mount can also be used on AXD-TR102 tripods with an adapter. Periodic errors on mounts are usually measured and corrected by the user. Unlike the old StarBook controller, the STAR BOOK TEN controller saves these errors permanently. The periodic error of the mount is measured in the factory (total of 12 points per 30 degrees worm gear) and corrected before delivery. This is known as V-PEC and functions automatically as soon as you use the mount. It delivers an accuracy of +/- 4.0 arc seconds. You can increase the tracking accuracy further by saving your own recorded periodic errors. Vixen uses a new Belt-drive system in the AXJ mount. The gear drive was replaced with a toothed belt drive. This gives the mount a quicker reaction time and lower backlash. It also helps to minimize noise. The 6x20 polar finder scope is pre-installed. This allows the user to configure the polar alignment (for both the northern and southern hemispheres). The polar finder scope has a variable illuminated reticle with an automatic power-off function. The brightness can be adjusted in 8 levels so that the user can configure the desired brightness. SETTING ACCURACY OF LESS THAN 3 ARC MINUTES The dark field illumination (red LED) turns on when the push button is pressed. The reticle also lights up in red so that the observer can recognize and align stars in the background of the reticle. The light turns off automatically after a few minutes to save battery power. 2 bearing sets (4 pieces) are used for the shaft of the RA axis. Thanks to the newly developed EQ design, the ZXJ mount has a higher load capacity of 22 kg. As the motors, worm shaft and worm gear are located in the lower part of the mount, fewer counterweights are required than with conventional mounts. The STAR BOOK TEN controller is a modern control system with a high-resolution colour monitor. The STAR BOOK TEN system contains more than 272,000 celestial objects, including 260,000 stars from the SAO catalogue, 109 Messier objects, 7840 NGC objects and 5380 IC objects, as well the soon, moon and planets. Objects can be accessed by name, and information such as images and data can be defined separately. FEATURES +/-4.0 arc seconds with V-PEC V-PEC (Vixen-Permanent Periodic Error Correction) Belt drive system (prevents backlash and minimizes noise) 14 ball bearings Polar alignment (variable fork fix type) Polar finder with reference star alignment STAR BOOK TEN controller with autoguider input Retractable counterweight bar WHAT’S INCLUDED AXJ mount Starbook Ten controller 2 counterweights (3.7 kg and 1.5 kg) GoTo mount with Star Book Ten controller 22 kg load (photographic)

Developed in order to store and protect the AXJ equatorial mount together with the StarBook TEN controller, the StarBook TEN cable and small accessories such as the power adapter. The housing is made from a newly developed material called Plapearl, which has an extremely long lifespan and is very lightweight. It consists of two plastic plates with vacuum-moulded cylinders that reduce the weight by 36% compared with conventional aluminium materials. It also offers high-grade airtight storage with only one opening and boasts attenuation properties that provide optimal protection for your equipment in terms of bending strength and resilience. FEATURES Material: Special polypropylene and aluminium alloy Colour: whiteDimensions: 47 cm x 49 cm x 23 cm Weight: 4.3 kgDELIVERY CONTENTAXJ case

A new 81 mm apochromatic refractor with high-performance Super ED glass (= SD). The advantage of these SD refractors is their short length and low weight.The FPL53 glass reproduces an extremely clear and sharp image due to an exceptionally high elimination of residual colour errors. The SD glass is designed to bring all rays of violet, red, blue, yellow and green together very precisely on the same plane. Thus, the special lens material reduces chromatic aberration across all colours.The new Vixen SD81SII no longer uses spacer plates, which leads to significantly better image quality, especially with bright stars. This means that there are no more spikes on the stars in photographic images, which were otherwise produced by the spacer plates. You will be thrilled when you look at the moon or the brighter planets and observe the moon craters pin sharp and with an extremely high contrast. Observe the ring planet Saturn or the cloud bands on Jupiter.But of course, brighter deep sky objects such as the Orion Nebula or the Andromeda Galaxy can also be observed impressively.In combination with the new optional SD Reducer HD Kit or SD Flattener HD, this refractor allows illumination with a 44 mm image circle for full-frame SLR cameras.The older ED81SII, ED103S, ED115S refractors were originally designed for the visual observer or the photographer using APS-C cameras. However, the new SD series has been optimised for use with full-frame cameras by inserting new inner baffle rings.The large 60 mm focuser allows heavy cameras to be attached without tilting. The supplied flip mirror allows comfortable observation, even in unfavourable observation situations, and also offers a T2 thread for connecting a DSLR camera.Thus, observing in degree view or at a 90° angle is possible. The carrying handle attached to the tube clamps ensures a secure hold when transporting the telescope.FEATURESObjective Lens: D=81 mm, multi-coated 2-Lens SD Apochromat without spacer plates No more spikes on the stars Focal Length: 625 mm (f7.7) Resolution and visual limit: 1.43 arcseconds; 11.3 Mag Light gathering capacity: 134x unaided eyesDimensions and weight: 90 mm dia x 585 mm, 3.6 kg Finderscope: XY Red Dot Finder II Adapter and connections: Adapter thread 60 mm and 31.7 mm for T2-ringConnection 50.8 mm and 31.7 mm socket with flip-mirror diagonal mirrorPhotography: primary focus and eyepiece projection SCOPE OF DELIVERY Refractor telescope SD81SII Tube rings Flip mirror system Carrying handle Dovetail rail Red dot viewfinder

Vixen has developed a new generation of SX mounts for demanding observers and astrophotographers. The SX2WL mount is simply operated via a Wifi module with a smartphone or tablet. By controlling the mount with your smartphone using the free STAR BOOK Wireless app, you can easily use sky navigation functions such as automatic GoTo panning of celestial objects via your smartphone or tablet. By eliminating the power consumption of the conventional LCD (STAR BOOK TEN), the power consumption on the mount is reduced by up to 20%, thus enabling longer astronomical observation and astrophotography. When the desired celestial object is selected from a list, it is automatically panned into the telescope's field of view and tracking begins.An existing STAR BOOK TEN controller can also be used on this mount without any problems. Equipped with the same precision stepper motors as the top model, the AXD mount, the SXD2WL brings a new standard of performance and precision to the Vixen mount family. With a photographic load capacity of 12 kg, the axis cross of the mount weighs just 7.0 kg (15.4 lbs) making it ideal for mobile observations.In addition, the motors mounted in the lower part of the mount also serve as a counterweight, so the mount requires fewer weights for balancing. The SX2 mount in detail Precision stepper motors and micro-step motion control systemAt the heart of the SXD2 are the precision stepper motors, which offer better performance and response than previous models. The micro-step motion control system offers powerful and yet very smooth drive characteristics, which are given both in fine movements and in fast pans. Built-in bearings The bearings of the RA and DEC axes and the worm shafts have been significantly improved to reduce the load on the motors. As a result, the motors move much more smoothly than in previous models. High-precision worm gearsHigh-precision processing technologies eliminate worm gear errors. The edges of the two worms and worm wheels are particularly smooth, enabling very precise tracking. Declination axis as counterweightThe solid motor units are installed in the lower part of the declination axis so that the center of gravity of the SXD2 is below the intersection point of the RA and DEC axes. This means you need fewer additional counterweights. Latitude setting The latitude is adjustable between 0 and 70 degrees (divided into 3 zones and adjustable +/- 15 degrees per zone, for high, medium and low latitudes); latitude scale in 2-degree increments; fine adjustment with a tangent screw head, approx. 0.8 degrees per turn. The wireless module in detail The Vixen Wifi adapter for EQ mounts allows you to control your Vixen mount via a smartphone or tablet. With the smartphone app STAR BOOK Wireless (free of charge) you can navigate the sky without any cables. The app turns your smartphone or tablet into a control unit for the equatorial mount in no time at all. The response delay of the mount, which is considered the biggest disadvantage of wireless connections, has been reduced to a level comparable to wired connections. Reduced power consumption compared to conventional controllers with LCD monitor The power consumption of the mount is reduced by up to 20%, allowing longer observations than with conventional wired controllers such as the STAR BOOK TEN. Operation similar to the STAR BOOK TEN controllerThe STAR BOOK Wireless app has a similar structure to the STAR BOOK TEN controller. Depending on the star map setting, it contains up to 259,000 celestial objects. Tap on a celestial object in the object list and start the GoTo. The mount will now automatically move to this target and bring it into the telescope's field of view. All the popular features of the STAR BOOK TEN are retained. Convenient operation When looking through the telescope operate the mount by swiping on the app's star chart. As there are no buttons, simply slide your finger over the star chart to operate the mount conveniently. Extensive astronomical data included In addition to data on easily observable celestial bodies such as Messier objects, NGC objects and IC objects, this also includes the sun, moon, planets, comets and dwarf planets. High-precision alignment By aligning the mount to one or two stars, you can already achieve fairly precise positioning. By aligning the mount to three or more stars, you can achieve high-precision alignment of the mount for high magnifications. The objects are then approached precisely and centrally in your telescope's field of view. The alignment information is saved and can be retained even when the device is switched off. By leaving the telescope in its current state after completing an observation without moving it, you can start the automatic installation with the same settings for the next observation.  Individual setting options As with the STAR BOOK TEN control unit, the app offers various individual settings, such as gear backlash compensation, night mode in red, autoguider and variable GoTo speed and LED brightness. You can also set the timing of the reversal of the objective tube (meridian flip) as desired. Even if the object moves to the south during tracking, you can prevent the telescope tube from reversing. Important note: Cannot be used on old SX mounts with the old blue Star Book! Technical information about the Wifi module: CPU with 32-bit CISC processor 120 MHz The unit is connected to the mount via a D-SUB 9PIN connector as with the STAR BOOK TEN. It has a 6-pin 6-wire modular plug for external autoguider operation. Supported operating systems are Android 6 or higher, iOS 9.0 or higher, WLAN standard: IEEE 802.11b/g/n. FEATURESRA sprocket: 180 teeth DEC sprocket: 180 teeth Shaft material and diameter: Carbon steel / Decl. 35 mm, RA 40 mm thickness  Fine height adjustment: 0° to 70°, (fine adjustment +/- 15°, height) Backsight rod: 20 mm diameter Azimuth adjustment: worm fine adjustment Power supply: DC12 V; 0.4~1.7 A Maximum load: 12 kg, photographic, without counterweight Counterweight: 1x 1.9 kg  Tripod connection: 45 mm spigot Dimensions: 36 cm (H) x 12 cm (W) x 36 cm (L), weight: 7.0 kg (15.4 lbs), without counterweight 32-bit CISC processor 120 MHz Operating system: Android 6 or higher, iOS 9.0 or higher Connection: D-SUB 9PIN connector Autoguider input: ST4 Power consumption SX2WL+Wireless unit: DC12V / 0.3-2.0 A (load 8 kg), 0.4-2.2 A (load 12 kg) SCOPE OF DELIVERYSX2WL EQ mount Wireless unit Counterweight: 1.9 kg (1pc) Mounting tools Cigarette lighter cable

The optics of the VMC260L are significantly better than the traditional Schmidt-Cassegrain telescope. Despite its high 3000 mm focal length, it is just 650 mm long. Featuring a large 260 mm aperture, the telescope collects large amounts of light for serious professional observations and photography of the planets and countless deep-sky objects. Thanks to the dielectric mirrors, the VMV260L guarantees razor-sharp images and maximum brightness. The open lens barrels cool the telescope quicker than conventional closed Cassegrain systems. The telescope can be used with an optional 0.62x focal reducer to reduce the aperture ratio to 1:7.1. This shortens the exposure times and allows you to photograph large objects. The telescope comes with a standard dovetail bar and a carry handle that doubles up as a camera holder for night sky photography. The Finder Scope and the Vixen Flip Mirror is not included in this version ! FEATURES Very short cool-down time thanks to open lens barrel Optimised system for photography Very transportable – only 650 mm long Lightweight design – only 12.1 kg Large 260 mm aperture Built-in correction lens in front of the secondary mirror Backfocus without Reducer: 149,4 mmBackfocus with Reducer: 63,5 mmTotal weight: 12.1 kg WHAT’S INCLUDED VMC 260 telescope/lens barrel Carry handle VIXEN standard dovetail barFinder Bracket ShoeEA60 mm to 50.8 mm SX

The new BRESSER Nebula 5 EQ/AZ Wifi-Network Mount is a precise and quiet telescope mount – ideal for astrophotography. The controller box offers numerous central connectivity options for various accessories such as cameras, filter wheels, and motor focusers via USB (2.0/3.0), simplifying the setup of a professional astrophotography machine. BRESSER has relied on innovation coupled with quality Made in Italy for this top-notch product. The manufacturer's long experience in mount construction guarantees a high-end device with first-class functionality and utmost reliability. Additionally, the in-house development team in Italy ensures quick response times in technical support and the adaptation of new device drivers. Truly, "Professionals at work!" The mount is controlled via pre-installed web-app software, accessible via WIFI and Ethernet cable connection. The philosophy behind the Nebula GoTo system is to provide the user with a control system independent of a standard PC, which can be remotely controlled via a smart device such as a mobile phone or tablet. However, this does not exclude the traditional use of computers of all types and brands, which can be connected to the system either wired or wirelessly. The BRESSER Nebula GoTo System Controller is a Raspberry Pi 4 microcomputer, which allows complete control of the setup (mount, camera, etc...) without the need for any other external device. The BRESSER Nebula GoTo system comes equipped with all Linux-based applications required for performing all astrophotographic functions.The existing INDI environment allows for the control of almost all devices (cameras, filter wheels, rotators, etc., including observatory domes) needed for local or remote astrophotography sessions. The system also offers high flexibility for users who prefer to use traditional computer client applications such as Cart du Ciel (Star Chart), TheSkyX, SkySafari, Stellarium, and other planetarium programs as well as SGP, Nina, CCD Ciel, and other astrophotography tools. This complete compatibility is ensured through the adoption of the Alpaca communication protocol, which allows for the use of traditional ASCOM platform drivers for native INDI devices.State-of-the-art mount construction The BRESSER Nebula mounts are CNC-manufactured from stainless steel and aluminium. The sleek and functional design is courtesy of a renowned Italian mount manufacturer, who has licensed the design and now manufactures these fine BRESSER products 100%. So, look forward to a stable yet easily portable mount, which despite its light weight of only 13 kg (incl. tripod), allows for a high load capacity of up to 20 kg.Visual Observation For visual observation and direct use, control the mount with the hand control box included in the package. Alternatively, connect the Nebula 5 via WLAN directly to your smartphone or tablet and use the virtual hand control box. Of course, all adjustment parameters can also be set via the web application. The user interface is deliberately simple and clear to ensure intuitive operation.Astrophotography Here, the Nebula mount shows its full strength. Whether mobile or stationary, the capability for remote operation is crucial. Connect your laptop or PC either via WLAN or with an Ethernet cable (recommended for faster data transmission) directly to the Raspberry-Pi control unit of the mount. Then use the pre-installed Kstars/EKOS software to control the mount and all external devices such as cameras, motor focus, filter wheel, etc. Alternatively, you can also directly control the unit with your own software. Applications such as Cart du Ciel (Star Chart), TheSkyX, SkySafari, Stellarium, and other planetarium programs as well as SGP, Nina, CCD Ciel, and other astrophotography tools can be used without any issues.2-in-1 Mount with EQ and AZ Mode If required, the Nebula can be switched from the equatorial mode to the azimuthal mode. This is particularly advantageous for observing nature or tracking satellites. Thus, the mount can be used for various applications and is not limited to astronomy.Attachment of up to two optics Would you like to adapt multiple optics? No problem. Simply use the option to replace the counterweight bar with another telescope. Use the second optic as a counterweight to the main telescope. Set the Nebula 5 to azimuthal mode, remove the counterweight bar, and screw a suitable second telescope clamp directly onto the mount. FEATURES Precise and quiet telescope mount – ideal for astrophotography Extensive connectivity options for various accessories via USB Integrated web app software enables central control of all components Integrated Raspberry Pi with USB-3 ports and Ethernet port Compatible with client applications such as Cart du Ciel (Star Chart), TheSkyX, SkySafari, Stellarium Compatible with SGP, Nina, CCD Ciel, and other astrophotography tools Virtual hand control box and settings menu for smartphones and tablets PC control – ASCOM and INDI compatible USB ports for cameras, motors, filter wheels, etc. Conversion from parallactic to azimuthal mode possible Small hand box for basic functions included High load capacity and yet lightweight Mount CNC-manufactured from stainless steel and aluminium Tooth belt drive for precise and quiet tracking Load capacity: 15 kg in EQ mode and 20 kg in AZ mode Dual prism clamping for Vixen GP and Losmandy Weight of the mount: 8 kg Weight of the tripod: 5 kg SCOPE OF DELIVERY Nebula 5 EQ/AZ Mount Field tripod Central control unit with Raspberry Pi Counterweight: 6 kg (1 piece) Basic hand box Connection cables Power supply 230V/12V/3A

The BRESSER 4CAST WIFI RC weather station not only provides a 4-day forecast but also numerous other meteorological data. With its simple but elegant design it is also a jewel for every home. Todays weather forecast and the forecast for the coming four days are always up-to-date and obtained from the weather service over the internet. The weather station communicates easily and conveniently with your WIFI network. Nevertheless, this weather station offers more than just your mobile phone or tablet, because in addition to the 4-day forecast, it also shows you the current room and exact outdoor values. In addition, the Humidex or Windchill values are displayed via the "Feels Like" display. The local indoor and outdoor temperature is measured via an integrated sensor or the supplied outdoor sensor. FEATURESLarge colour display RC weather station incl. power plug 5-day Weather Forecast for today and the following 4 days for your location Continuous free updates via your WIFI network Accurate and current weather data from the weather service Rain probability calculated by real MeteorologistsReal forecast of wind speed and wind direction for today Relative air pressure display Time and calendar synchronization via WIFI connection5-day weather forecast including high and low temperatures WIFI Signal Display Humidex or Windchill readings via the "Feels Like" display Local weather data acquisition via your outdoor sensor: Max 3 sensors connectable for outdoor temperature measurementIndoor and outdoor temperature display Indoor and outdoor humidity display SCOPE OF SUPPLY 4CAST Weather station 1x Outdoor sensor Power supply unit Instruction manual