Whether in the photo or film studio, or for camping and leisure, the BRESSER BR-21 gooseneck is always a good helper for attaching photo studio accessories and other utensils. With two different clamps, the flexible arm is quickly and flexibly attached to table tops or tripos.The stable and flexible component has a total length of 43 cm and can be stowed away quickly to save space. Books, reflectors, microphones, leisure equipment and much more - there is hardly anything that the BRESSER Gooseneck cannot hold. The rubberised screw clamp with an opening of 0,5 to 3,5 cm can also be mounted on tubes and rods, microphone stands or lamp tripods. The rubberised spring clamp with its robust width of 7,5 cm has a maximum opening of 5 cm. Conveniently, the BRESSER BR-21 can also be used in reverse. The spring clamp can be used as a table clamp and screw clamp can be used as a holder for tubes, rods ect.NOTE: The load capacity of approx. 1-2 kg depends on the angle of inclination and may therefore vary.PROPERTIESFlexible bendable arm 43 cm/ Ø 15 mmTotal length: 62 cmMetal clamp with strong spring on one side, screw clamp on the other sideRemoveable rubber lipsSpring clamp opnening: max 5,5 cmClamp width: 7,5 cmTube clamp width: 4 cm/ length: 5 cmScrew clamp opening: 0,5 cm - 3,5 cmLoad capacity: max 1-2 kg, depending on angle of inclinationSCOPE OF DELIVERY1x BRESSER BR-21 Flexarm
When cleaning high quality optical lenses, you have to be very careful. After all, it would be very annoying to successfully remove the dust but leave a scratch behind. With the BRESSER BR-LP10 lens cleaning pen you can safely clean optical and coated glass. With the brush on one side you can remove coarser dirt before polishing the lenses with the other side.
FEATURES
lens cleaning pencil for safe cleaning of optical and coated glass
brush to remove dust on one sidepolishing pad on the other side
SCOPE OF DELIVERY
1x lens cleaning pencil
The BRESSER BR-LP20 cleaning kit is designed for thoroughly cleaning equipment and lenses. This set contains four handy cleaning tools:
Rubber blowerWith this, you can blow dust and small particles off the lens or camera without touching it. This prevents scratches or damage that can occur from direct contact.
BrushA soft brush for removing more stubborn dirt that is not easily blown away. It is designed to be soft enough to avoid causing scratches.
Cleaning fluidSpecial fluid for cleaning the lens without leaving streaks or residue. Although the fluid is not harmful, it is advised to avoid inhalation and contact with eyes and skin.
Microfiber clothA soft cloth used in combination with the cleaning fluid to wipe the lens or camera clean. Microfiber is ideal for absorbing grease and fingerprints without scratching the surface.
This set is an essential toolkit for photography enthusiasts who want to keep their equipment in top condition. Using the right cleaning tools like these helps to extend the lifespan of your equipment.
SCOPE OF DELIVERY
1x Rubber blower
1x Brush
1x Bottle of cleaning fluid
1x Lint-free cloth
Whether in the photo or film studio, for camping or leisure activities, the BRESSER BR-20 gooseneck is always a good helper for attaching photo studio accessories and other utensils. With two sturdy spring clamps, the flexible arm is quickly and flexibly attached to table tops or tripods.The flexible part measures 43 cm in length and with a total length of 64 cm, the gooseneck can be quickly stowed away to save space. Books, reflectors, microphones, leisure equipment and much more - there is hardly anything that the BRESSER BR-20 Gooseneck will not hold. The rubberized spring clips with a width of 7,5 cm and an opening of up 5 cm can also be attached to tubes and rods, microphone stands and lamp tripods.NOTE: The load capacity of up to 1 kg depends on the angle of inclination and may therefore vary.PROPERTIESFlexible bendable arm: 43 cm/ Ø 15 mmTotal length: 64 cmRemovable rubber lipsSpring clamp opening: max. 5,5 cmClamp width: 75 mmLoad capacity: max. 1 Kg, dependig on angle of inclinationSCOPE OF DELIVERY1x BRESSER BR-20 Flex Arm
The universal BRESSER BR-141 smartphone holder is designed for devices with a width of 5 to 15 cm. The smartphone clamps into the adjustable holder and can be turned to the desired position. The strong and sturdy clamp on the other side allows the holder to be attached to a table, shelf or bar. The maximum load is 400 g.
FEATURES
Fully flexible and adjustable smartphone holder
Designed for devices with a width of 5 to 15 cm
400 g maximum load
Strong clamp for securing the holder to a table, shelf or bar
WHAT’S INCLUDED
1x smartphone holder
he BRESSER TR-688V is a solid video tripod at a small price!
The three tripod legs can be individually adjusted in length thanks to the practical quick-release buckles. The rubber feet can be angled as required. So you can find stable stand even on slopes and on uneven ground. Ideal for photographing outdoors!
360 ° shots are not a problem with the 2-way tilt. With the help of the handgrip, the tripod head can be rotated 360 ° smoothly. In addition, the camera can be tilted up to 90 ° over two axes. An integrated water scale and canister bubble ensure the required precision.
Want to quickly switch between cameras with different lenses and settings? With the quick-release plate is no problem!
FEATURES
especially lightweight and transportable
suitable for cameras and spotting scopes up to a total weight of 3 kg
infinitely height adjustable from 63.5 cm to 171 cm
2-way tilt with quick-release plate
1/4 "photo screw
two integrated circular levels
individually adjustable tripod legs for uneven terrain
by hand crank extendable column
Hook for attachment of a counterweight for more stability
SCOPE OF DELIVERY
Video tripod with 2-way tilt
Quick release plate
Tripod bag with shoulder strap
This universal clamp can be attached to a shooting table, a shelf or a desk. Also very suitable to fix background paper and cloth.FEATURESsturdy metal clampstrong metal springremovable rubber lipswidth: 8 cmmax. opening: 6 cm SCOPE OF DELIVERY5x studio clamp
With the BRESSER B-RS 180 trolley, the BRESSER CR-1 ceiling rail system can be extended to attach further photo studio accessories or pantographs.The metal bracket allows the trolley to be pushed into position on the rails and serves as a damper and brake.PROPERTIESSpigot adapter for various accessoriesDamper with metal bracketVariable useMaximum felxibilty thanks to the spigot adapterSCOPE OF DELIVERYSingle trolley for ceiling track
When there is no assistant around to hold the collapsible reflector for you during a photo shoot the BRESSER BR-6 clamp support offers the optimal solution. The metal clamp with a strong spring safely holds even larger reflectors. Thereby, the rubber lips protect the reflectors against any damages. This clamp is attached onto a tilt head, so you can position the reflector flexibly for an ideal illumination.The support clamp is equipped with a removable adapter with two different threads so it can be put onto any lightstand.FEATURESmetal clamp to attach collapsible reflectors to lightstandstilt headopening for studio umbrellasexchangeable tripod connectionSCOPE OF DELIVERYsupport clampspigot adapter (1/4" female, 3/8" female)
Universal clamp with a strong spigot adapter. The bracket can be clamped to a photo shooting table, shelf or table. Studio lamps or flashes with a tripod thread fit on the universal spigot adapter.FEATURESversatile clampstrong springreversible rubber lipsstable spigot adapter 1/4"max. opening: 6 cmsuitable for studio lights and flashesSCOPE OF DELIVERY1x Clamp with Spigot Adapter
This universal clamp can be attached to a shooting table, a shelf or a desk. Also very suitable to fix background paper and cloth.FEATURESsturdy metal clampstrong metal springremovable rubber lipswidth: 9 cmmax. opening: 6 cm SCOPE OF DELIVERY1x studio clamp
A strong pipe clamp made of metal which can be screwed onto a light stand thanks to the 3/8'' female thread on the lower side of the clamp. This way a crossbar with a thikness of 25 mm to 35 mm can be put onto the light stand.FEATURESsolid metal pipe clampdiameter: 25 - 35 mm3/8'' female thread on its lower sideSCOPE OF DELIVERY1x Pipe Clamp 35mm
The robust BRESSER BR-23 gooseneck can be quickly and easily mounted anywhere on tables or boards. LED lights, panel lights, light photo studio flashes and various daylight lights can be mounted on the screwed-in spigot connection with a 1/4" screw thread. In addition, mini LED lights etc. can also be screwed on. The flexible part of the gooseneck has a length of 44 cm and has a load capacity of approx. 1 - 2 kg, taking into account the angle of inclination. With its total length of 60 cm, the practical BRESSER BR-23 gooseneck can be stored quickly and space-saving in the photo studio equipment.Note: The load capacity of approx. 1-2 kg depends on the tilt angle and may therefore vary.PROPERTIESFlexible, bendable arm: 43 cm/ Ø 15 mmRubberised spring clamp with strong spring1/4" spigot adapterClamp opening: max. 55 mmClamp width: 80 mmLoad capacity: 1- 2 kgSCOPE OF DELIVERY1x Flex arm1x Spigot 2,5 cm
Paper backgrounds often tend to roll up at the bottom end. This BRESSER weighted bar is designed to stop the paper from moving and ensure a tight background for your photographs.
Simply attach the weighted bar to the end of the paper roll with the adhesive tape provided. Small spirit levels on both sides of the bar help to ensure that the background is mounted in a level position.
FEATURES
280 cm long bar for weighting paper backgrounds
Prevents unwanted rolling
Spirit levels on both sides to ensure level installation
Collapses into 3 parts for transport and storage
WHAT’S INCLUDED
3-part weighted bar
Adhesive tape
A strong wall bracket of metal, which can be mounted on the wall or the ceiling. You can put a flash head or other accessories on the spigot adapter.FEATURESuniversal wall bracketsize: 6 cm highspigot adapter 5/8" without threadSCOPE OF DELIVERY1x universal wall bracket
The BRESSER BR-TP440R PRO-1 lamp tripod is the ideal basic equipment for photography and videography. The light stand is equipped with spring damping and can bear loads of up to 5 kg. The spigot connection with 1/4" and 3/8" inch thread can be used to quickly attach an LED panel light, a photo studio flash, a ring light and a reflector.The 105 cm footprint ensures a stable stand even outdoors and on uneven ground, even with the centre column fully extended to a maximum height of 440 cm.PROPERTIES3 section aluminium lamp tripodFolded height 120 cmMaximum stand width 105 cmTube diameter of stand feet approx. 23 mmMinimum height: 135 cmMaximum height: 440 cmRemoveable 1/4" and 3/8" inch spigot adapterMaximum load 4-5 kgSCOPE OF DELIVERY1x BRESSER BR-TP440R PRO-1
A handy and universal metal clamp to attach background paper, background cloth or collapsible reflectors to a rod or pipe. With this clamp you can for instance prevent a background roll from unrolling. NOTE!These clamps are attached to the side of the background roll, the core of the roll and the crossbar of the background system (NOT onto the background roll itself)FEATURESsolid metal background clamplength: ca. 15 cmopening: ca. 5,5 cmweight: 70 gSCOPE OF DELIVERY1x background clamp
A strong and stable aluminium light stand which can easily be folded to a compact size. The supplied spigot adapter can be attached either vertical or horizontal to the tripod top. There is an air spring system in the tripod, which absorbs possible shocks when lowering the flash head. All connecting elements are made of metal. To prevent any reflection, the aluminium is provided with a black powder coating.FEATURESaluminium lightstandexchangeable spigot adapterheigth: 100 - 220 cmfolded height: 82 cmSCOPE OF DELIVERY1x light stand1x spigot adapter (1/4" male, 3/8" male)
The universal plastic studio clamps are very handy and have a very strong spring. The clamps can be used versatily in the photo studio, e.g. for the attachment of paper or vinyl to a table and for the securing of small accessories, rods or reflectors. There are moveable red clamp jaws at the end of the clamps which results in a secure grip and an equal pressure on the clamped object.FEATURESstrong springmoveable clamp jawssize: 6.5 x 5.5 cmopening (max.): 3 cmweight: 8 g eachSCOPE OF DELIVERY5x studio clamp 6.5 cm
The practical BRESSER JM-46 lamp holder is suitable for both ceiling and wall mounting. A useful solution for confined spaces or small film or photo studios. The telescopic extension from 37 to 60 cm provides flexibility in lightning. The two-sided spigot connection with a 1/4" and a 3/8" thread makes it easy to attach LED panel lights, photo studio flashes, daylight lamps, monitors and also photo and video cams.PROPERTIESCeiling/ Wall lamp mountTelescopic extension from 37 to 54 cmSturdy mounting plate: 12 x 8 cm1/4" and 3/8" spigot connectionSCOPE OF DELIVERY1x BRESSER JM-46 wall arm1x Spigot adapter
The robust BRESSER BR-23B gooseneck can be quickly and easily attached anywhere to tables, tubes and tripods using the tube clamp. On the screwed-in spigot connection with a 1/4" screw thread, various daylight lamps can be mounted from LED lamps, panel lamps, light photo studio flashes. In addition, mini LED lights etc. can also be screwed on. The flexible part of the gooseneck has a length of 43 cm and has a load capacity of approx. 1 - 2 kg, taking into account the angle of inclination. With its total length of 59 cm, the practical BRESSER BR-23 gooseneck can be quickly stowed away in the photo studio equipment to save space.NOTE: The load capacity of approx. 1 - 2 kg depends on the tilt angle and may therefore vary.
FEATURESFlexible bendable arm: 43 cm/ Ø 15 mm
Total length: 59 cmScrew clamp opening (maximum): 35 mmScrew/ tube clamp: W: 4 cm x L: 7,5 cm x D: 6cmLoad capacity: max 1 - 2 kg, depending on angle of inclination
SCOPE OF DELIVERY
FlexarmSpigot adapter (1/4'' male / 3/8'' male)
This set of 10 BRESSER BR-65 tighteners for cloth backgrounds attaches to background systems via a hook and loop fastener. A small clip is attached to the cloth background, which can then be tightened with the elastic band. The tighteners ensure that your background is kept tight and crease-free.
The set includes a total of 10 tighteners.
FEATURES
10 tighteners
Attaches to background system with hook and loop fastener
Small clips for holding the cloth background
Cloth background is tightened via elastic band
Rubber band min. 20 cm long
WHAT’S INCLUDED
10x tighteners
A strong and stable aluminium light stand which can be folded easily to compact dimensions. There is an air suspension system in the tripod, which can stabilize any vibration caused by lowering the flash head. To prevent any reflection the aluminium is provided with a black powder coating.FEATURESaluminium light standair suspension system for shock absorptionblack powder coating to prevent undesired reflections adjustable height: 134 - 400 cmSCOPE OF DELIVERY 1x light stand1x spigot adapter (1/4" male, 3/8" male)
We use cookies to personalise and improve content and services, deliver relevant advertising and provide a secure experience. You can review your cookie controls at any time. Learn more about the use and control of cookies in our privacy policy.Imprint
Functional cookies are absolutely necessary for the functionality of the web shop. These cookies assign a unique random ID to your browser so that your unhindered shopping experience can be guaranteed over several page views.
Google Pay payments
Amazon Pay
Stripe orig props:
Stripe referrer information.
Private machine identifier cookie:
Security token to identify the private machine.
Site auth:
Stripe authentication cookie.
Stripe csrf:
CSRF token.
PayPal payments
Cookie settings:
The cookie is used to store the cookie settings of the site user over several browser sessions.
Information on origin:
The cookie stores the referrer and the first page visited by the user for further use.
Payment provider (Stripe) session
Timezone:
The cookie is used to provide the system with the user's current time zone.
CAPTCHA integration
Payment provider (Stripe) session
Stripe:
The cookie is used by the payment provider to increase security when processing payments on the website.
Cache handling:
The cookie is used to differentiate the cache for different scenarios and page users.
Session:
The session cookie stores your shopping data over several page views and is therefore essential for your personal shopping experience.
Payment provider (Stripe) fraud prevention
Payment provider (Stripe) fraud prevention
CSRF token:
The CSRF token cookie contributes to your security. It strengthens the security of forms against unwanted hacker attacks.
Google Tag Manager debug mode:
Allows to run the Google Tag Manager in debug mode.
Activated cookies:
Saves which cookies have already been accepted by the user for the first time.
YouTube video
Location maps:
We use OpenStreetMap as tile provider to show you visually the location of our stores and merchants.
Recently viewed products:
The cookie stores the most recently viewed products in order to suggest them on further product pages.
Wishlist
Customers also viewed:
The cookie stores the most recently viewed products in order to suggest them to other customers on product pages.
Cookies used for statistics and shop performance metrics.
Conversion and usertracking via Google Tag Manager
Google Tag Manager:
Cookie from Google to control the advanced script and event handling.
Google Analytics:
Cookie from Google for website analysis. Generates statistical data about how the visitor uses the website.
Tracking cookies help the shop operator to collect and evaluate information about the behaviour of users on their website.
Matomo Tracking:
Tracking statistics for the optimization of user workflows. No personal data is stored.
Google Analytics:
Google Analytics is used for traffic analysis of the website. Thereby statistics about website activities can be created and read out.
Marketing cookies are used to display advertisements on the website in a targeted and individualized manner across multiple page views and browser sessions.
Google Advertising
Google Ads:
Advertising Targeting
Google AdSense:
The cookie is used by Google AdSense to promote advertising efficiency on the website.
Google conversion tracking:
The Google Conversion Tracking Cookie is used to track conversions on the website effectively. This information is used by the site operator to target Google AdWords campaigns.
To watch videos, you need to accept third-party cookies: